2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 2654
* Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 gal) Tank Rear) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 43.5L (11.5 Gal) Tank Rear))Fuel Tank
Fuel Pump Module Replacement (2500 LWB - 98.4L (26 gal) Tank Front) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (2500 LWB - 98.4L (26 Gal) Tank Front))Fuel Tank
Fuel Pump Module Replacement (1500 SWB - 98.4L (26 gal) Tank + E85) (See: Powertrain Management/Fuel Delivery and Air
Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module Replacement (1500 SWB - 98.4L (26 Gal) Tank + E85))Fuel Tank
Fuel Pump Module Replacement (1500 Series) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and
Repair/Fuel Tank Fuel Pump Module Replacement (1500 Series))Fuel Tank Fuel Pump Module Replacement (1500 LWB - 117.3L (31 gal)
Tank + E85) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Service and Repair/Fuel Tank Fuel Pump Module
Replacement (1500 LWB - 117.3L (31 Gal) Tank + E85))
* Relay Replacement (Attached to Wire Harness) (See: Power and Ground Distribution/Power Distribution Relay/Service and Repair/Relay
Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (See: Power and Ground Distribution/Power
Distribution Relay/Service and Repair/Relay Replacement (Within an Electrical Center))
* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming
6L50/6L80/6L90 - Automatic Transmission
DTC P2714 or P2715
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC P2714
- Clutch Pressure Control (PC) Solenoid 4 - Stuck Off
DTC P2715
- Clutch Pressure Control (PC) Solenoid 4 - Stuck On
Circuit/System Description
The clutch pressure control (PC) solenoid 4 is part of the control solenoid valve assembly, which has no serviceable parts. The PC solenoid 4
regulates transmission fluid pressure to the 2-6 clutch regulator valve which controls pressure to the 2-6 clutch. The TCM calculates gear ratio
based on the RPM signals from the input speed sensor (ISS) and the output speed sensor (OSS). The TCM compares the expected transmission gear
ratio to the calculated gear ratio for each commanded gear.
Conditions for Running the DTC
P2714
* DTCs P0716, P0717, P0722, P0723, P1825, or P1915 are not set.
* The transmission input shaft speed is greater than 60 RPM.
* 2-6 clutch is commanded ON.
P2715
* DTCs P0716, P0717, P0722, P0723, P1825, or P1915 are not set.
* The transmission output shaft speed is greater than 200 RPM.
* 2-6 clutch is commanded OFF.
Conditions for Setting the DTC
P2714
The TCM detects an incorrect on-coming clutch gear ratio, or flare, when the 2-6 clutch is commanded ON for 0.5 seconds and the transmission
input shaft speed is greater than 75 RPM from the anticipated input shaft speed.
P2715
The TCM detects an incorrect off-going clutch gear ratio, or tie-up, when the 2-6 clutch is commanded OFF for 0.5 seconds and the transmission
input shaft speed is greater than 40 RPM from the anticipated input shaft speed.
Action Taken When the DTC Sets
