2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 990
Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
C123C
DTC C056D, C120C, C121C, C121E, C121F, C123A-C1256, C126E-C127C, C12C2-C12DB, C12DE, C12DF, or C12F2-C12F6
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provide an overview of each diagnostic category.
DTC Descriptors
DTC C056D 00
- ECU Hardware Performance
DTC C056D 3C
- ECU Hardware Performance Internal Communications Failure
DTC C056D 59
- ECU Hardware Performance
DTC C120C
- Brake Pedal Position Sensor 4 Plausibility
DTC C121C
- EBCM Internal Communication Error
DTC C121E
- EBCM Unimplemented Interrupt
DTC C121F
- EBCM Unexpected Exception
DTC C123A
- EBCM High End Timer Watchdog
DTC C123B
- EBCM High End Timer Program Overflow
DTC C123C
- EBCM High End Timer RAM Fault
DTC C123D
- EBCM Solenoid Timeout
DTC C123E
- EBCM High End Timer Periodic Interrupt
DTC C123F
- EBCM Serial Peripheral Interface Inoperative
DTC C1255
- Electronic Control Unit Performance
DTC C1256
- Program ROM Checksum Error
DTC C126E
- EBCM Stack Overrun
DTC C126F
- EBCM Serial Peripheral Interface Performance
Showing posts with label Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement. Show all posts
Showing posts with label Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement. Show all posts
Thursday, December 19, 2019
Thursday, December 12, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 831
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 831
Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
Brake Boost Solenoid
DTC C012F, C12A7, C12DC, or C12DD
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C012F 00
- Brake Boost Solenoid Valve Circuit
DTC C012F 0E
- Brake Boost Solenoid Valve Circuit Shorted
DTC C12A7
- Brake Boost Solenoid Valve Circuit Performance
DTC C12DC
- Brake Boost Solenoid Valve Circuit Malfunction
DTC C12DD
- Brake Boost Solenoid Valve Circuit Shorted
Circuit/System Description
The electronic brake control module (EBCM) uses input from the boost pressure sensor for more accurate control during brake and vehicle stability
enhancement system (VSES) event. The boost pressure sensor is internal to the brake pressure modulator valve (BPMV).
Conditions for Running the DTC
* The ignition is ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
C012F 00, C12A7, C12DC
Solonoid feedback current greater than 25% of commanded current.
C012F 0E, C12DD
Solonoid feedback current greater than 50% of requested current.
Action Taken When the DTC Sets
* The EBCM disables the ABS/traction control system (TCS)/vehicle stability enhancement system (VSES) for the duration of the ignition
cycle.
* A DIC message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for setting the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
Brake Boost Solenoid
DTC C012F, C12A7, C12DC, or C12DD
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C012F 00
- Brake Boost Solenoid Valve Circuit
DTC C012F 0E
- Brake Boost Solenoid Valve Circuit Shorted
DTC C12A7
- Brake Boost Solenoid Valve Circuit Performance
DTC C12DC
- Brake Boost Solenoid Valve Circuit Malfunction
DTC C12DD
- Brake Boost Solenoid Valve Circuit Shorted
Circuit/System Description
The electronic brake control module (EBCM) uses input from the boost pressure sensor for more accurate control during brake and vehicle stability
enhancement system (VSES) event. The boost pressure sensor is internal to the brake pressure modulator valve (BPMV).
Conditions for Running the DTC
* The ignition is ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
C012F 00, C12A7, C12DC
Solonoid feedback current greater than 25% of commanded current.
C012F 0E, C12DD
Solonoid feedback current greater than 50% of requested current.
Action Taken When the DTC Sets
* The EBCM disables the ABS/traction control system (TCS)/vehicle stability enhancement system (VSES) for the duration of the ignition
cycle.
* A DIC message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for setting the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Sunday, November 17, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 863
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 863
* Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, programming and setup
Antilock Brake System - Non-Hybrid Greater than/Equal to 3900 kg (8600 lb) GVW
DTC C0186 or C0196
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC C0186 55
- Lateral Accelerometer Circuit Expected Number of Transition/Events Exceeded
DTC C0186 5A
- Lateral Accelerometer Circuit Plausibility Failure
DTC C0186 0F
- Lateral Accelerometer Circuit Erratic
DTC C0196 55
- Yaw Rate Circuit Expected Number of Transition/Events Exceeded
DTC C0196 5A
- Yaw Rate Circuit Plausibility Failure
DTC C0196 0F
- Yaw Rate Circuit Erratic
Circuit/System Description
The lateral accelerometer and the yaw rate sensors are combined into one sensor external to the electronic brake control module (EBCM). The
vehicle stability enhancement system (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The EBCM recieves the
yaw/lateral accelerometer sensor data from dedicated serial data circuits.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
* The yaw/lateral accelerometer sensor fails an internal self test.
* The correlation error between the yaw/lateral accelerometer sensor and steering angle sensor.
Actions Taken when the DTC Sets
* The EBCM disables the StabiliTrak for the duration of the ignition cycle.
* A DIC message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Diagnostic Aids
An incorrectly mounted sensor can cause these faults.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, programming and setup
Antilock Brake System - Non-Hybrid Greater than/Equal to 3900 kg (8600 lb) GVW
DTC C0186 or C0196
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions)provides an overview of each diagnostic category.
DTC Descriptors
DTC C0186 55
- Lateral Accelerometer Circuit Expected Number of Transition/Events Exceeded
DTC C0186 5A
- Lateral Accelerometer Circuit Plausibility Failure
DTC C0186 0F
- Lateral Accelerometer Circuit Erratic
DTC C0196 55
- Yaw Rate Circuit Expected Number of Transition/Events Exceeded
DTC C0196 5A
- Yaw Rate Circuit Plausibility Failure
DTC C0196 0F
- Yaw Rate Circuit Erratic
Circuit/System Description
The lateral accelerometer and the yaw rate sensors are combined into one sensor external to the electronic brake control module (EBCM). The
vehicle stability enhancement system (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The EBCM recieves the
yaw/lateral accelerometer sensor data from dedicated serial data circuits.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
* The yaw/lateral accelerometer sensor fails an internal self test.
* The correlation error between the yaw/lateral accelerometer sensor and steering angle sensor.
Actions Taken when the DTC Sets
* The EBCM disables the StabiliTrak for the duration of the ignition cycle.
* A DIC message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Diagnostic Aids
An incorrectly mounted sensor can cause these faults.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 861
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 861
Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
Antilock Brake System - Non-Hybrid Less than 3900 kg (8600 lb) GVW
DTC C0186 or C0196
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C0186 00
- Lateral Accelerometer Circuit
DTC C0186 5A
- Lateral Accelerometer Circuit Plausibility Failure
DTC C0196 00
- Yaw Rate Circuit
DTC C0196 5A
- Yaw Rate Circuit Plausibility Failure
Diagnostic Fault Information
Circuit/System Description
The yaw rate and the lateral accelerometer sensors are combined into one sensor, external to the electronic brake control module (EBCM). The
vehicle stability enhancement system (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The EBCM supplies the 12
V to the yaw/lateral accelerometer sensor. The yaw/lateral accelerometer sensor communicates with the EBCM via discrete CAN Bus High and
CAN Bus Low serial data circuits.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
* Short to ground on the CAN High serial data circuit.
* The yaw/lateral accelerometer sensor fails an internal self test.
* Communication is lost between the EBCM and the yaw/lateral combination sensor.
* The correlation error between the yaw/lateral combination sensor and steering angle sensor.
Action Taken When the DTC Sets
One or more of the following actions may occur:
* The EBCM disables the antilock brake system (ABS)/traction control system (TCS) and vehicle stability enhancement system (VSES) for the
duration of the ignition cycle.
* The ABS indicator illuminates.
* The red Brake warning indicator illuminates.
Control Module References (See: Testing and Inspection/Programming and Relearning) for EBCM replacement, setup, and programming
Antilock Brake System - Non-Hybrid Less than 3900 kg (8600 lb) GVW
DTC C0186 or C0196
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptors
DTC C0186 00
- Lateral Accelerometer Circuit
DTC C0186 5A
- Lateral Accelerometer Circuit Plausibility Failure
DTC C0196 00
- Yaw Rate Circuit
DTC C0196 5A
- Yaw Rate Circuit Plausibility Failure
Diagnostic Fault Information
Circuit/System Description
The yaw rate and the lateral accelerometer sensors are combined into one sensor, external to the electronic brake control module (EBCM). The
vehicle stability enhancement system (VSES) uses the lateral accelerometer input when calculating the desired yaw rate. The EBCM supplies the 12
V to the yaw/lateral accelerometer sensor. The yaw/lateral accelerometer sensor communicates with the EBCM via discrete CAN Bus High and
CAN Bus Low serial data circuits.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
* Short to ground on the CAN High serial data circuit.
* The yaw/lateral accelerometer sensor fails an internal self test.
* Communication is lost between the EBCM and the yaw/lateral combination sensor.
* The correlation error between the yaw/lateral combination sensor and steering angle sensor.
Action Taken When the DTC Sets
One or more of the following actions may occur:
* The EBCM disables the antilock brake system (ABS)/traction control system (TCS) and vehicle stability enhancement system (VSES) for the
duration of the ignition cycle.
* The ABS indicator illuminates.
* The red Brake warning indicator illuminates.
Subscribe to:
Posts (Atom)