2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 825
DTC C12F4
- ABS Proportioning Valve Solenoid Performance
DTC C12F5
- ABS Right Rear Isolation Solenoid Circuit Shorted
DTC C12F6
- ABS Right Rear Isolation Solenoid Performance
Circuit/System Description
The electronic brake control module (EBCM) detects an internal malfunction.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM detects an internal malfunction.
Action Taken When the DTC Sets
* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the
ignition cycle.
* A driver information center message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Test for less than 1 ohm between the ground circuits listed below and ground.
* Terminal 13
* Terminal 38
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
Showing posts with label DTC C12F4. Show all posts
Showing posts with label DTC C12F4. Show all posts
Thursday, December 12, 2019
Wednesday, December 11, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 815
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 815
DTC C12F4
- ABS Proportioning Valve Solenoid Performance
DTC C12F5
- ABS Right Rear Isolation Solenoid Circuit Shorted
DTC C12F6
- ABS Right Rear Isolation Solenoid Performance
Circuit/System Description
The electronic brake control module (EBCM) detects an internal malfunction.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM detects an internal malfunction.
Action Taken When the DTC Sets
* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the
ignition cycle.
* A driver information center message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Test for less than 1 ohm between the ground circuits listed below and ground.
* Terminal 13
* Terminal 38
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
DTC C12F4
- ABS Proportioning Valve Solenoid Performance
DTC C12F5
- ABS Right Rear Isolation Solenoid Circuit Shorted
DTC C12F6
- ABS Right Rear Isolation Solenoid Performance
Circuit/System Description
The electronic brake control module (EBCM) detects an internal malfunction.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM detects an internal malfunction.
Action Taken When the DTC Sets
* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the
ignition cycle.
* A driver information center message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Test for less than 1 ohm between the ground circuits listed below and ground.
* Terminal 13
* Terminal 38
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 805
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 805
DTC C12F4
- ABS Proportioning Valve Solenoid Performance
DTC C12F5
- ABS Right Rear Isolation Solenoid Circuit Shorted
DTC C12F6
- ABS Right Rear Isolation Solenoid Performance
Circuit/System Description
The electronic brake control module (EBCM) detects an internal malfunction.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM detects an internal malfunction.
Action Taken When the DTC Sets
* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the
ignition cycle.
* A driver information center message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Test for less than 1 ohm between the ground circuits listed below and ground.
* Terminal 13
* Terminal 38
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
DTC C12F4
- ABS Proportioning Valve Solenoid Performance
DTC C12F5
- ABS Right Rear Isolation Solenoid Circuit Shorted
DTC C12F6
- ABS Right Rear Isolation Solenoid Performance
Circuit/System Description
The electronic brake control module (EBCM) detects an internal malfunction.
Conditions for Running the DTC
* Ignition ON.
* Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM detects an internal malfunction.
Action Taken When the DTC Sets
* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the
ignition cycle.
* A driver information center message and/or a warning indicator may be displayed.
Conditions for Clearing the DTC
* The condition for the DTC is no longer present.
* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.
Reference Information
Schematic Reference
Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)
Connector End View Reference
Component Connector End Views (See: Diagrams/Connector Views)
Description and Operation
ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS
Description and Operation)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the EBCM.
2. Test for less than 1 ohm between the ground circuits listed below and ground.
* Terminal 13
* Terminal 38
瀚慖f greater than the specified range, test the ground circuit for an open/high resistance.
Subscribe to:
Posts (Atom)