Showing posts with label Diagnostic Fault Information. Show all posts
Showing posts with label Diagnostic Fault Information. Show all posts

Tuesday, December 17, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 95

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 95

Diagnostic Fault Information

Circuit/System Description

If a malfunction is detected, a DTC will be stored in non-volatile memory. During a frontal crash of sufficient force the inflatable restraint sensing

and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the driver steering wheel air bag. The

SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.

There are 2 shorting bars used within each connector which will short together both driver steering wheel air bag stage 1 high circuit and driver

steering wheel air bag stage 1 low circuit and both driver steering wheel air bag stage 2 high circuit and driver steering wheel air bag stage 2 low

circuit when the connector is disconnected. This will help to prevent unwanted deployment of the air bag during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0012 01 Stage 1 or B0013 01 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to voltage for 120 milliseconds.

B0012 02 Stage 1 or B0013 02 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to ground for 120 milliseconds.

B0012 04 Stage 1 or B0013 04 Stage 2

The driver steering wheel air bag high and/or low circuit is open for 120 milliseconds.

B0012 0D Stage 1 or B0013 0D Stage 2

The driver steering wheel air bag deployment loop resistance is greater than 5.1 ohms for 120 milliseconds.

B0012 0E Stage 1 or B0013 0E Stage 2

The driver steering wheel air bag deployment loop resistance is less than 1.3 ohms for 120 milliseconds.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

* The condition for setting the DTC no longer exists.

* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.

Diagnostic Aids

* When a harness connector is disconnected, the high control and low control circuits are shorted together by the integral shorting bar. This

should be taken into account when testing for faults on these circuits.

* This DTC usually indicates a poor connection or a wiring malfunction between the SDM and the deployment loop.

Reference Information

Schematic Reference

SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Monday, December 16, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 919

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 919

Diagnostic Fault Information

Circuit/System Description

The electronic brake control module (EBCM) uses input from the brake master cylinder piston position sensor and the brake switch to determine

when the brake pedal is being applied and with how much force. These inputs are used to determine the driver's braking intent which is used to the

control amount of pressure applied to the wheels.

Conditions for Running the DTC

* Ignition ON.

* Ignition voltage is greater than 10 volts.

Conditions for Setting the DTC

C0277 03, C129A, or C129D

The EBCM detects voltage below threshold on signal circuit.

C0277 07, C129B, or C129E

The EBCM detects voltage above threshold on signal circuit.

C0277 5A, C12B1, C12F8, or C120C

This EBCM detects the master cylinder pressure is high when brake master cylinder piston position sensor is reading low travel.

Action Taken When the DTC Sets

* The EBCM disables the antilock brake system (ABS), traction control and the vehicle stability enhancement system for the duration of the

ignition cycle.

* A driver information center message and/or a warning indicator may be displayed.

Conditions for Clearing the DTC

* The condition for the DTC is no longer present.

* The EBCM clears the history DTC when a current DTC is not detected in 40 consecutive drive cycles.

Reference Information

Schematic Reference

Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation/ABS

Description and Operation)

Electrical Information Reference

Wednesday, December 4, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 650

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 650

Diagnostic Fault Information

Circuit/System Description

The body control module (BCM) controls the horn relay by grounding the control circuit of the horn relay coil energizing the relay. When the horn

relay is energized, the horn relay contacts close applying voltage through the horn fuse and the horn control circuit to the horns.

Conditions for Running the DTC

When the output is actively being requested by the BCM.

Conditions for Setting the DTC

The BCM detects a short to ground, open or short to battery in the horn relay control circuit for approximately 125 milliseconds.

Action Taken When the DTC Sets

The BCM disables the output to the horn relay until the next ignition cycle.

Conditions for Clearing the DTC

* The DTC clears when the fault is no longer detected.

* The current DTC will become history when the request for the output is removed.

* The history DTC will clear after 50 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Horn Schematics (See: Lighting and Horns/Horn/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Horns System Description and Operation (See: Lighting and Horns/Horn/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Command the horn ON and OFF with the scan tool. The horn should turn ON and OFF when changing between the commanded states.

Circuit/System Testing

1. Ignition OFF, disconnect the X4 harness connector at the underhood fuse block.

2. Connect a test lamp between the control circuit terminal G1 and B+.

3. Press and release the horn switch. The test lamp should turn ON and OFF when changing between the commanded states.

Thursday, November 28, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 540

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 540

Diagnostic Fault Information

Circuit/System Description

The front seat heating elements are controlled by a common high current relay internal to the heated seat control module (HSM) and on the low side

by individual element control circuits. The HSM connects the seat heater element supply voltage circuits to a common reference point. This

reference point is biased to approximately 2.5 V. Before the HSM will allow heated seat operation, it checks to see if the heating element supply

voltage circuits and control circuits are shorted to ground or battery voltage. Once the HSM verifies that it is not closing into a shorted heating

element, it allows heated seat operation. After which it continues to monitor for a shorted circuit.

Conditions for Running the DTC

The HSM must be powered.

Conditions for Setting the DTC

B2345 00

After a heated seat is activated, the HSM detects a shorted circuit on the seat heating element supply voltage circuit or control circuit.

B2345 13

Any of the temperature sensor inputs remains below 1.45 V for more than 1 second.

B2345 42

The current sensing calibration is not programmed.

B2345 4B

The current sensing calibration is out of range.

Monday, November 25, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 458

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 458

Diagnostic Fault Information

Circuit/System Description

The retained accessory power (RAP) system allows specific vehicle functions to operate after the ignition is turned OFF for a predetermined time.

The RAP relay is internal to the BCM. Relay RAP is controlled by the BCM using inputs from the door ajar switches to determine control of the

relay when the ignition is turned OFF. Radio RAP is controlled by a serial data message from the BCM using inputs from the driver door open

switch. Refer to Retained Accessory Power Description and Operation (See: Power and Ground Distribution/Description and Operation/Retained

Accessory Power Description and Operation) for more detail on RAP operation.

Conditions for Running the DTC

* The system voltage is between 9-16 volts.

* The DTC can only set when the output is actively being requested by the module.

Conditions for Setting the DTC

The DTC will set only when the module requests the output and there is a short to ground detected in the RAP supply voltage circuit.

Action Taken When the DTC Sets

The BCM output driver will be shut down and not supply voltage to the circuit.

Conditions for Clearing the DTC

* The current DTC will clear when the module request for the output is removed or the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Diagnostic Aids

* The RAP/Spare relay is permanently soldered to the left I/P junction block and is non-serviceable.

* The RAP mode for the radio and door modules is a separate function and will still operate properly.

Reference Information

Schematic Reference

Power Moding Schematics (See: Diagrams/Electrical Diagrams/Starting and Charging/Power and Ground Distribution/System Diagram/Power

Moding Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Retained Accessory Power Description and Operation (See: Power and Ground Distribution/Description and Operation/Retained Accessory Power

Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition ON, verify DTC B1475 is set as current.

Tuesday, November 19, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 980

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 980

Diagnostic Fault Information

Circuit/System Description

The electronic suspension control (ESC) module supplies a 5 volt reference signal to each suspension position sensor. The suspension position

sensors supply an voltage signal of 0.35-4.75 volts to the ESC module which represents the position between the body and the wheel. The sensors

are also grounded through the ESC module.

Conditions for Running the DTC

* Battery voltage is between 9-16 volts

* Ignition is ON

Conditions for Setting the DTC

* The DTC is set when the ESC module measures a position sensor signal voltage below 0.35 volt or above 4.75 volts for more than 1 second

while the vehicle is operated under normal driving conditions.

* The fault is detected during 3 consecutive ignition cycles, or during the same ignition cycle after clearing the DTC with a scan tool.

Action Taken When the DTC Sets

* The ESC will enter the speed dependent damping mode.

* Both left and right normal force outputs will be set to the default output states.

* The ESC sends a message to the instrument panel cluster (IPC) to display SERVICE SUSPENSION SYSTEM message.

Conditions for Clearing the DTC

A history DTC will clear after 50 consecutive ignition cycles if the condition for the malfunction is no longer present.

Reference Information

Schematic Reference

Electronic Suspension Control Schematics (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Diagrams/Electrical Diagrams/Electronic Suspension Control)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Description and Operation/Electronic Suspension Control Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

Monday, November 18, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 95

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 95

Diagnostic Fault Information

Circuit/System Description

If a malfunction is detected, a DTC will be stored in non-volatile memory. During a frontal crash of sufficient force the inflatable restraint sensing

and diagnostic module (SDM) will allow current to flow through the deployment loop in order to deploy the driver steering wheel air bag. The

SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity and for shorts to ground or voltage.

There are 2 shorting bars used within each connector which will short together both driver steering wheel air bag stage 1 high circuit and driver

steering wheel air bag stage 1 low circuit and both driver steering wheel air bag stage 2 high circuit and driver steering wheel air bag stage 2 low

circuit when the connector is disconnected. This will help to prevent unwanted deployment of the air bag during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 volts.

Conditions for Setting the DTC

B0012 01 Stage 1 or B0013 01 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to voltage for 120 milliseconds.

B0012 02 Stage 1 or B0013 02 Stage 2

The driver steering wheel air bag high and/or low circuit is shorted to ground for 120 milliseconds.

B0012 04 Stage 1 or B0013 04 Stage 2

The driver steering wheel air bag high and/or low circuit is open for 120 milliseconds.

B0012 0D Stage 1 or B0013 0D Stage 2

The driver steering wheel air bag deployment loop resistance is greater than 5.1 ohms for 120 milliseconds.

B0012 0E Stage 1 or B0013 0E Stage 2

The driver steering wheel air bag deployment loop resistance is less than 1.3 ohms for 120 milliseconds.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

* The condition for setting the DTC no longer exists.

* A history DTC will clear once 100 malfunction-free ignition cycles have occurred.

Diagnostic Aids

* When a harness connector is disconnected, the high control and low control circuits are shorted together by the integral shorting bar. This

should be taken into account when testing for faults on these circuits.

* This DTC usually indicates a poor connection or a wiring malfunction between the SDM and the deployment loop.

Reference Information

Schematic Reference

SIR Schematics (See: Diagrams/Electrical Diagrams/Air Bag Systems)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Sunday, November 17, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 834

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 834

Diagnostic Fault Information

Circuit/System Description

The wheel speed sensor receives ignition voltage from the electronic brake control module (EBCM) and provides a DC square wave signal back to

the module. As the wheel spins, the EBCM uses the frequency of the square wave signal to calculate the wheel speed.

Conditions for Running the DTC

C0035 02 and 05-C0050 02 and 05

Ignition ON.

C0035 18-C0050 18

* Ignition ON.

* No other wheel speed circuit DTCs are set.

* The brake pedal is not pressed.

* Two or three other wheel speeds are greater than 0 km/h.

C0035 0F-C0050 0F

* Ignition ON.

* The brake pedal is not pressed.

* A DTC is not set for the other wheel speed circuit on the same axle.

Conditions for Setting the DTC

C0035 02-C0050 02

A short to ground is detected on the wheel speed 12-volt reference or signal circuit.

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 819

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 819

Diagnostic Fault Information

Circuit/System Description

The wheel speed sensor receives ignition voltage from the electronic brake control module (EBCM) and provides a DC square wave signal back to

the module. As the wheel spins, the EBCM uses the frequency of the square wave signal to calculate the wheel speed.

Conditions for Running the DTC

C0035 02 and 05-C0050 02 and 05

Ignition ON.

C0035 18-C0050 18

* Ignition ON.

* No other wheel speed circuit DTCs are set.

* The brake pedal is not pressed.

* Two or three other wheel speeds are greater than 0 km/h.

C0035 0F-C0050 0F

* Ignition ON.

* The brake pedal is not pressed.

* A DTC is not set for the other wheel speed circuit on the same axle.

Conditions for Setting the DTC

C0035 02-C0050 02

A short to ground is detected on the wheel speed 12-volt reference or signal circuit.

Saturday, November 16, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 723

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 723

Diagnostic Fault Information

Circuit/System Description

The LOCK/UNLOCK relay is controlled by the body control module (BCM) by providing voltage to one side of the relay or providing a ground to

the other side of the relay. During lock or unlock operation, battery voltage will be supplied to the lock actuators through the energized side of the

relay and grounded through the de-energized side of the relay.

Conditions for Running the DTC

The system voltage must be between 9-16 volts.

Conditions for Setting the DTC

B3130 00

The BCM detects a fault on the REAR DOOR LOCK/UNLOCK relay control circuit while commanding the rear doors to unlock.

B3135 00

The BCM detects a fault on the REAR DOOR LOCK/UNLOCK relay control circuit while commanding the rear doors to lock.

Action Taken When the DTC Sets

The rear power door locks will malfunction.

Conditions for Clearing the DTC

* The DTC will be current for as long as the fault is present.

* When the fault is no longer present, the DTC will become a history DTC.

* A history DTC will clear after 50 ignition cycles.

Reference Information

Schematic Reference

Door Lock/Indicator Schematics (See: Body and Frame/Locks/Diagrams/Electrical Diagrams/Door Lock/Indicator Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Description and Operation

Power Door Locks Description and Operation (See: Body and Frame/Locks/Power Locks/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Wednesday, November 13, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 484

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 484

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The battery current sensor is a 3-wire hall effect current sensor. The battery current sensor monitors the battery current. The signal circuit is an

input to the body control module (BCM). The sensor creates a 5-volt pulse width modulation (PWM) signal of 128 Hz with a duty cycle of 0-100

percent. Normal duty cycle is between 4-96 percent. The signal circuit is an input to the body control module (BCM). If the duty cycle is outside of

the normal range, DTC B1516 08 sets. The BCM also tests for correct polarity of the sensor. If the BCM detects positive current flow with the

engine OFF, DTC B1516 66 sets.

Conditions for Running the DTC

B1516 08

The BCM is awake.

B1516 66

* The BCM is awake.

* The engine is OFF.

* The hood and doors are closed.

* DTC B1516 08 has run and passed during this ignition cycle.

* DTC B1516 66 has not already run and passed during this ignition cycle.

Conditions for Setting the DTC

B1516 08

The BCM detects the sensor signal duty cycle is less than 4 percent or greater than 96 percent for 2 minutes.

B1516 66

The BCM detects positive battery current when the engine is OFF.

Action Taken When the DTC Sets

Regulated voltage control (RVC) is disabled.

Conditions for Clearing the DTC

* The DTC passes when the battery sensed current returns to the normal range for 15 seconds.

Friday, November 8, 2019

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 106

2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 106

Diagnostic Fault Information

Circuit/System Description

During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the

deployment loop in order to deploy the air bag module. There are 2 shorting bars used within the module connector which will short together both

high and low circuits, when the connector is disconnected. This will prevent unwanted deployment of the inflator module during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 V.

Conditions for Setting the DTC

B0014 01, B0015 01, B0016 01, B0019 01, B0020 01, B0021 01, B0022 01, B0023 01

The air bag or seat belt retractor pretensioner high and/or low control circuit is shorted to voltage for 120 milliseconds.

B0014 02, B0015 02, B0016 02, B0019 02, B0020 02, B0021 02, B0022 02, B0023 02

The air bag or seat belt retractor pretensioner high and/or low control circuit is shorted to ground for 120 milliseconds.

B0014 04, B0015 04, B0016 04, B0019 04, B0020 04, B0021 04, B0022 04, B0023 04

The air bag or seat belt retractor pretensioner high and/or low control circuit is open for 120 milliseconds.

B0014 0D, B0015 0D, B0016 0D, B0019 0D, B0020 0D, B0021 0D, B0022 0D, B0023 0D

The air bag or seat belt retractor pretensioner deployment loop resistance is greater than 3.9 ohms for 120 milliseconds.

B0014 0E, B0015 0E, B0016 0E, B0019 0E, B0020 0E, B0021 0E, B0022 0E, B0023 0E

The air bag or seat belt retractor pretensioner deployment loop resistance is less than 1.1 ohm for 120 milliseconds.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

Tuesday, November 5, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1193

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1193

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The motor temperature sensor (MTS) is a non-serviceable part of the drive motor generator assembly. The MTS sensor is a thermistor, or a resistor

that changes value when the temperature changes. The sensor has a negative-temperature coefficient. This means that as the temperature increases,

the resistance decreases, and as the temperature decreases, the resistance increases. The motor control module (MCM) supplies about a 5-volt

reference signal to the sensor and measures the voltage drop in the circuit. When the motor is cold, the sensor resistance is high and the MCM

detects high signal voltage. As the motor temperature increases, the resistance of the sensor decreases, which lowers the signal voltage.

Conditions for Running the DTC

P0A2B and P0A31

* DTCs P0A2C, P0A2D, P0AEF, P0AF0, P0BD3, P0BD4, P0BDD, P0BDE are not set.

* Ignition ON after the engine has been OFF for at least 6 hours.

* Average of phase U, V, W inverter temperatures is greater than -12掳C (+10掳F).

* Motor temperature is greater than -40掳C (-40掳F).

P0A2C, P0A2D, P0A32 and P0A33

The ignition is ON.

Conditions for Setting the DTC

P0A2B and P0A31

* The average of the three motor phase sensor temperatures and the motor temperature are not within 28掳C (50掳F) of each other at ignition ON.

* The DTC sets within 3 seconds when the above condition is met.

P0A2C and P0A32

* Motor temperature sensor signal is less than 0.29V.

* The DTC sets within 3 seconds when the above condition is met.

P0A2D and P0A33

Motor temperature sensor signal is greater than 4.42V.

If this condition is observed at Ignition ON, the drive motor generator must operate at greater than 20 Nm (14.75 lb ft) of torque for a cumulative

time of 1.5 minutes before the DTC will set.

If this condition is observed after Ignition ON, the DTC will set within 3 seconds when the above condition is met.

Action Taken When the DTC Sets

* DTCs P0A2B-P0A2D, P0A31-P0A33 are Type B DTCs.

* The HPCM commands the SERVICE HYBRID SYSTEM message to display on the instrument panel.

Conditions for Clearing the DTC

DTCs P0A2B-P0A2D, P0A31-P0A33 are Type B DTCs.

Diagnostic Aids

* The motor temperature sensor can be damaged by excessive electric current. Test the sensor for an open condition whenever a short to

voltage condition is observed.

Monday, November 4, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 106

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 106

Diagnostic Fault Information

Circuit/System Description

During a side or frontal crash of sufficient force the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the

deployment loop in order to deploy the air bag module. There are 2 shorting bars used within the module connector which will short together both

high and low circuits, when the connector is disconnected. This will prevent unwanted deployment of the inflator module during servicing.

Conditions for Running the DTC

Ignition voltage is between 9-16 V.

Conditions for Setting the DTC

B0014 01, B0015 01, B0016 01, B0019 01, B0020 01, B0021 01, B0022 01, B0023 01

The air bag or seat belt retractor pretensioner high and/or low control circuit is shorted to voltage for 120 milliseconds.

B0014 02, B0015 02, B0016 02, B0019 02, B0020 02, B0021 02, B0022 02, B0023 02

The air bag or seat belt retractor pretensioner high and/or low control circuit is shorted to ground for 120 milliseconds.

B0014 04, B0015 04, B0016 04, B0019 04, B0020 04, B0021 04, B0022 04, B0023 04

The air bag or seat belt retractor pretensioner high and/or low control circuit is open for 120 milliseconds.

B0014 0D, B0015 0D, B0016 0D, B0019 0D, B0020 0D, B0021 0D, B0022 0D, B0023 0D

The air bag or seat belt retractor pretensioner deployment loop resistance is greater than 3.9 ohms for 120 milliseconds.

B0014 0E, B0015 0E, B0016 0E, B0019 0E, B0020 0E, B0021 0E, B0022 0E, B0023 0E

The air bag or seat belt retractor pretensioner deployment loop resistance is less than 1.1 ohm for 120 milliseconds.

Action Taken When the DTC Sets

* The SDM requests the instrument panel cluster (IPC) to illuminate the AIR BAG indicator.

* The SDM will store a DTC, however if an event occurs the system will still attempt deployments.

Conditions for Clearing the DTC

Saturday, November 2, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1892

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1892

Diagnostic Fault Information

Circuit/System Description

The heated oxygen sensors (HO2S) are used for fuel control and catalyst monitoring. Each HO2S compares the oxygen content of the surrounding

air with the oxygen content of the exhaust stream. When the engine is started, the control module operates in an Open Loop mode, ignoring the

HO2S signal voltage while calculating the air-to-fuel ratio. While the engine runs, the HO2S heats up and begins to generate a voltage within a

range of 0-1,275 mV. Once sufficient HO2S voltage fluctuation is observed by the control module, Closed Loop is entered. The control module

uses the HO2S voltage to determine the air-to-fuel ratio. An HO2S voltage that increases toward 1,000 mV indicates a rich fuel mixture. An HO2S

voltage that decreases toward 0 mV indicates a lean fuel mixture.

The heating elements inside each HO2S heat the sensor to bring the sensor up to operating conditions faster. This allows the system to enter Closed

Loop earlier and the control module to calculate the air-to-fuel ratio sooner.

Conditions for Running the DTC

P0133, P0153, P1133, or P1153

* DTCs P0068, P0101, P0102, P0103, P0106, P0107, P0108, P0112, P0113, P0116, P0117, P0118, P0120, P0121, P0122, P0123, P0128,

P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0220, P0222, P0223, P0442, P0443, P0446, P0449, P0455, P0496, P1516,

P2101, P2119, P2135, P2176 are not set.

* The engine coolant temperature (ECT) is greater than 60锟斤拷C (140锟斤拷F).

* The intake air temperature (IAT) is warmer than -40锟斤拷C (-40锟斤拷F)

* The ignition 1 voltage is between 10-32 V.

* The fuel level is greater than 10 %.

* The engine run time is greater than 160 s.

* The engine speed is between 1,200-3,000 RPM.

* The barometric (BARO) pressure is greater than 70 kPa.

* The mass airflow (MAF) is between 20-55 g/s.

* The fuel system is in Closed Loop.

* The throttle position (TP) is greater than 5 %.

* The DTCs run once per drive cycle when the above conditions are met.

P013A P013C, P013E, or P014A

* Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass.

* Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222,

P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are

not set.

* The ignition 1 voltage is between 10-32 V.

* The learned heater resistance is valid.

* The fuel level is greater than 10 %.

* The engine run time is equal to or greater than 5 minutes.

* The accelerator pedal (APP) is steady.

* The torque converter clutch (TCC) is applied.

* The DTCs run once per ignition cycle, during decel fuel cut-off (DFCO), when the above conditions are met.

P013B P013D, P013F, or P014B

* Before the ECM can report DTC P013B, or P013D failed, DTCs P013A, P013C, P013E, P013F, P014A, P014B, P2270, P2271, P2272, and

P2273 must run and pass.

* Before the ECM can report DTC P013F, or P014B failed, DTCs P013A, P013C, P013E, P014A, P2270, P2271, P2272, and P2273 must run

and pass.

* DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133,

Friday, November 1, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1854

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1854

Diagnostic Fault Information

Typical Scan Tool Data

Circuit Description

The manifold absolute pressure (MAP) sensor measures the pressure inside the intake manifold. Pressure in the intake manifold is affected by

engine speed, throttle opening, air temperature, and barometric pressure (BARO). A diaphragm within the MAP sensor is displaced by the pressure

changes that occur from the varying load and operating conditions of the engine. The sensor translates this action into electrical resistance. The

MAP sensor wiring includes 3 circuits. The engine control module (ECM) supplies a regulated 5 volts to the sensor on a 5-volt reference circuit.

The ECM supplies a ground on a low reference circuit. The MAP sensor provides a signal voltage to the ECM, relative to the pressure changes, on

the MAP sensor signal circuit. The ECM converts the signal voltage input to a pressure value.

Under normal operation the highest pressure that can exist in the intake manifold is equal to BARO. This occurs when the vehicle is operated at

wide-open throttle (WOT) or when the ignition is ON while the engine is OFF. Under these conditions, the ECM uses the MAP sensor to determine

the current BARO. The lowest manifold pressures occur when the vehicle is idling or decelerating. MAP can range from 10 kPa, when pressures

are low, to as much as 104 kPa when pressures are high, depending on the BARO. The ECM monitors the MAP sensor signal for pressure outside

of the normal range.

Conditions for Running the DTC

P0107

* DTCs P0641, P0651, P1516, P2101, P2125, P2135, P2138, P2176 are not set.

* The engine speed is greater than 400 RPM.

* The throttle angle is greater than 0 percent when the engine speed is less than 800 RPM.

OR

* The throttle angle is greater than 13 percent when the engine speed is greater than 800 RPM.

* This DTC runs continuously when the above conditions are met.

P0108

* DTCs P1516, P2101, P2125, P2135, P2138, P2176 are not set.

* The engine has been running for a period of time that is determined by the start-up engine coolant temperature (ECT). The time ranges from

8 seconds at less than -30锟斤拷C (-22锟斤拷F) to 3 seconds at greater than 30锟斤拷C (86锟斤拷F).

* The throttle angle is less than 1 percent when the engine speed is less than 1,200 RPM.

OR

* The throttle angle is less than 20 percent when the engine speed is greater than 1,200 RPM.

* This DTC runs continuously when the above conditions are met.

Conditions for Setting the DTC

P0107

The ECM detects that the MAP sensor voltage is less than 0.1 volt for more than 4 seconds.

P0108

The ECM detects that the MAP sensor voltage is more than 4.9 volts for greater than 4 seconds.

Action Taken When the DTC Sets

DTCs P0107 and P0108 are Type B DTCs.

Saturday, October 26, 2019

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1193

2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1193

Diagnostic Fault Information

Typical Scan Tool Data

Circuit/System Description

The motor temperature sensor (MTS) is a non-serviceable part of the drive motor generator assembly. The MTS sensor is a thermistor, or a resistor

that changes value when the temperature changes. The sensor has a negative-temperature coefficient. This means that as the temperature increases,

the resistance decreases, and as the temperature decreases, the resistance increases. The motor control module (MCM) supplies about a 5-volt

reference signal to the sensor and measures the voltage drop in the circuit. When the motor is cold, the sensor resistance is high and the MCM

detects high signal voltage. As the motor temperature increases, the resistance of the sensor decreases, which lowers the signal voltage.

Conditions for Running the DTC

P0A2B and P0A31

* DTCs P0A2C, P0A2D, P0AEF, P0AF0, P0BD3, P0BD4, P0BDD, P0BDE are not set.

* Ignition ON after the engine has been OFF for at least 6 hours.

* Average of phase U, V, W inverter temperatures is greater than -12锟斤拷C (+10锟斤拷F).

* Motor temperature is greater than -40锟斤拷C (-40锟斤拷F).

P0A2C, P0A2D, P0A32 and P0A33

The ignition is ON.

Conditions for Setting the DTC

P0A2B and P0A31

* The average of the three motor phase sensor temperatures and the motor temperature are not within 28锟斤拷C (50锟斤拷F) of each other at ignition ON.

* The DTC sets within 3 seconds when the above condition is met.

P0A2C and P0A32

* Motor temperature sensor signal is less than 0.29V.

* The DTC sets within 3 seconds when the above condition is met.

P0A2D and P0A33

Motor temperature sensor signal is greater than 4.42V.

If this condition is observed at Ignition ON, the drive motor generator must operate at greater than 20 Nm (14.75 lb ft) of torque for a cumulative

time of 1.5 minutes before the DTC will set.

If this condition is observed after Ignition ON, the DTC will set within 3 seconds when the above condition is met.

Action Taken When the DTC Sets

* DTCs P0A2B-P0A2D, P0A31-P0A33 are Type B DTCs.

* The HPCM commands the SERVICE HYBRID SYSTEM message to display on the instrument panel.

Conditions for Clearing the DTC

DTCs P0A2B-P0A2D, P0A31-P0A33 are Type B DTCs.

Diagnostic Aids

* The motor temperature sensor can be damaged by excessive electric current. Test the sensor for an open condition whenever a short to

voltage condition is observed.