2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1497
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Circuit/System Verification
1. Clear the DTC information.
2. Turn the ignition OFF for 2 minutes.
3. Turn the ignition ON.
4. Operate the vehicle within the conditions for running and setting.
5. Retest for the DTC.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Perform the High Voltage Disabling () procedure for servicing at the drive motor generator control module cable connections.
2. Remove the 3-phase cable assembly from the PIM distribution box. Refer to Generator Control Module 3-Phase Cable Assembly
Replacement ().
3. Test the resistance to ground for each phase of the applicable drive motor generator by measuring between the following points with a DMM.
* Phase U terminal and chassis ground
* Phase V terminal and chassis ground
* Phase W terminal and chassis ground
瀚慖f less than infinite is measured, continue with Circuit/System Testing.
瀚慖f infinite resistance is measured, replace the drive motor generator assembly that corresponds to the set DTC and retest for DTCs. If
DTC P0C01 or P0C04 still resets, replace the PIM.
4. Remove the 3-phase cable assembly from the transmission. Refer to Generator Control Module 3-Phase Cable Assembly Replacement ().
Ensure the terminals are not contacting chassis ground.
5. Retest the resistance to ground for each phase of the 3-phase cable. Measure between the following points with a DMM.
* Phase U terminal and the shield ground
* Phase V terminal and the shield ground
* Phase W terminal and the shield ground
瀚慖f infinite resistance is measured, replace the applicable drive motor generator.
瀚慖f less than infinite is measured, replace the generator control module 3-phase cable assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
* Generator Control Module 3-Phase Cable Assembly Replacement ()
* Drive Motor with Generator Assembly Removal - 1st Position (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic Transmission/8. Drive Motor with Generator Assembly Removal -
Showing posts with label Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code. Show all posts
Showing posts with label Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code. Show all posts
Saturday, November 9, 2019
Friday, November 8, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1386
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1386
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
* EL-48571 High Voltage Battery Pin Out Box
* EL-48900 HEV Safety Kit
Circuit/System Verification
Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V, and all readings should be within 1.5
V of each other.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B9D
DTC P0B3E, P0B43, P0B48, P0B4D, P0B52, P0B57, P0B5C, P0B61, P0B66, P0B6B, P0B70, P0B75, P0B7A, P0B7F, P0B84, P0B89, P0B8E,
P0B93, P0B98, or P0B9D
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
* EL-48571 High Voltage Battery Pin Out Box
* EL-48900 HEV Safety Kit
Circuit/System Verification
Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V, and all readings should be within 1.5
V of each other.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
瀚慖f not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
瀚慖f not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B9D
DTC P0B3E, P0B43, P0B48, P0B4D, P0B52, P0B57, P0B5C, P0B61, P0B66, P0B6B, P0B70, P0B75, P0B7A, P0B7F, P0B84, P0B89, P0B8E,
P0B93, P0B98, or P0B9D
Thursday, November 7, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1297
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1297
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Ignition ON.
4. Retest for DTCs P0BE6, P0BE7, P0BE8, P0BEA, P0BEB, P0BEC, P0BEE, P0BEF, P0BF0, P0BF2, P0BF3, P0BF4, P0BF6, P0BF7,
P0BF8, P0BFA, P0BFB or P0BFC.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE8
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0BE6
- Drive Motor 1 Phase U Current Sensor Performance
DTC P0BE7
- Drive Motor 1 Phase U Current Sensor Circuit Low Voltage
DTC P0BE8
- Drive Motor 1 Phase U Current Sensor Circuit High Voltage
DTC P0BEA
- Drive Motor 1 Phase V Current Sensor Performance
DTC P0BEB
- Drive Motor 1 Phase V Current Sensor Circuit Low Voltage
DTC P0BEC
- Drive Motor 1 Phase V Current Sensor Circuit High Voltage
DTC P0BEE
- Drive Motor 1 Phase W Current Sensor Performance
DTC P0BEF
- Drive Motor 1 Phase W Current Sensor Circuit Low Voltage
DTC P0BF0
- Drive Motor 1 Phase W Current Sensor Circuit High Voltage
DTC P0BF2
- Drive Motor 2 Phase U Current Sensor Performance
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Ignition ON.
4. Retest for DTCs P0BE6, P0BE7, P0BE8, P0BEA, P0BEB, P0BEC, P0BEE, P0BEF, P0BF0, P0BF2, P0BF3, P0BF4, P0BF6, P0BF7,
P0BF8, P0BFA, P0BFB or P0BFC.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE8
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0BE6
- Drive Motor 1 Phase U Current Sensor Performance
DTC P0BE7
- Drive Motor 1 Phase U Current Sensor Circuit Low Voltage
DTC P0BE8
- Drive Motor 1 Phase U Current Sensor Circuit High Voltage
DTC P0BEA
- Drive Motor 1 Phase V Current Sensor Performance
DTC P0BEB
- Drive Motor 1 Phase V Current Sensor Circuit Low Voltage
DTC P0BEC
- Drive Motor 1 Phase V Current Sensor Circuit High Voltage
DTC P0BEE
- Drive Motor 1 Phase W Current Sensor Performance
DTC P0BEF
- Drive Motor 1 Phase W Current Sensor Circuit Low Voltage
DTC P0BF0
- Drive Motor 1 Phase W Current Sensor Circuit High Voltage
DTC P0BF2
- Drive Motor 2 Phase U Current Sensor Performance
Wednesday, November 6, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1222
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1222
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Tuesday, November 5, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1146
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1146
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1143
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1143
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1140
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 1140
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95掳C (-38.2 and
+203掳F) with no greater than a 15掳C ( 59掳F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
瀚慖f any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
瀚慖f not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Friday, November 1, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1837
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1837
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Verify that DTCs P0721, P0722, P0723, P0756, P0757, P0796, P0797, P0966, P0967, P0969, P0970, P0971, P0973, P0974, P0976, P0977,
P2720, P2721, P2728, P2729, P2730, P2797, or P0C2B is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing
and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check)
to verify correct fluid level and condition.
3. Verify using Freeze Frame and Failure Records, the Aux. Trans. Fluid Pump Actual parameter is within 25 percent of the Aux. Trans. Fluid
Pump Commanded parameter.
锟斤拷If the Aux. Trans. Fluid Pump Actual parameter is not within 25 percent of the Aux. Trans. Fluid Pump Commanded parameter, refer to
Auxiliary Fluid Pump Pressure High or Low (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Auxiliary Fluid Pump Pressure High or Low).
4. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check) to verify correct oil pressure.
5. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control
Solenoid Valve and Transmission Control Module Assembly Inspection) to verify control solenoid valve assembly condition.
6. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and
Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic
Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test) to verify control solenoid
valve assembly function.
7. Inspect the trans fluid pump ball check valve for possible sticking or damage.
锟斤拷If you found a concern with the check ball, repair the concern.
8. Inspect the hybrid low, 1-2 clutch regulator valve for sticking or damage.
锟斤拷If you found a concern with the hybrid low, 1-2 clutch regulator valve, repair or replace the valve or valve body.
9. Inspect the hybrid low, 1-2 clutch assembly for wear or damage.
锟斤拷If you found a hybrid low, 1-2 clutch assembly concern, repair or replace the low and reverse clutch assembly as necessary.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Valve Assembly Disassemble (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and
Repair/Overhaul/2ML70 - Automatic Transmission/54. Control Valve Assembly Disassemble) for valve body inspection procedures.
* Control Valve Upper Body Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and
Repair/2ML70 - Automatic Transmission) for control valve body replacement.
* Hybrid Low, 1-2 Clutch Piston Removal (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and
Repair/Overhaul/2ML70 - Automatic Transmission/24. Hybrid Low, 1-2 Clutch Piston Removal) for hybrid low, 1-2 clutch assembly
inspection.
* Hybrid Low, 1-2 Clutch Piston Installation (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and
Repair/Overhaul/2ML70 - Automatic Transmission/31. Hybrid Low, 1-2 Clutch Piston Installation) for low and hybrid low, 1-2 clutch
assembly replacement.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,
setup, and programming.
P079B
DTC P079B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Verify that DTCs P0721, P0722, P0723, P0756, P0757, P0796, P0797, P0966, P0967, P0969, P0970, P0971, P0973, P0974, P0976, P0977,
P2720, P2721, P2728, P2729, P2730, P2797, or P0C2B is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).
2. Perform the Transmission Fluid Level and Condition Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing
and Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Transmission Fluid Level and Condition Check)
to verify correct fluid level and condition.
3. Verify using Freeze Frame and Failure Records, the Aux. Trans. Fluid Pump Actual parameter is within 25 percent of the Aux. Trans. Fluid
Pump Commanded parameter.
锟斤拷If the Aux. Trans. Fluid Pump Actual parameter is not within 25 percent of the Aux. Trans. Fluid Pump Commanded parameter, refer to
Auxiliary Fluid Pump Pressure High or Low (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Symptom Related Diagnostic Procedures/2ML70 - Automatic Transmission/Auxiliary Fluid Pump Pressure High or Low).
4. Perform the Line Pressure Check (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component
Tests and General Diagnostics/2ML70 - Automatic Transmission/Line Pressure Check) to verify correct oil pressure.
5. Perform the Control Solenoid Valve and Transmission Control Module Assembly Inspection (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic Transmission/Control
Solenoid Valve and Transmission Control Module Assembly Inspection) to verify control solenoid valve assembly condition.
6. Perform the Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test (See: Transmission and
Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Component Tests and General Diagnostics/2ML70 - Automatic
Transmission/Control Solenoid Valve and Transmission Control Module Assembly Solenoid Performance Test) to verify control solenoid
valve assembly function.
7. Inspect the trans fluid pump ball check valve for possible sticking or damage.
锟斤拷If you found a concern with the check ball, repair the concern.
8. Inspect the hybrid low, 1-2 clutch regulator valve for sticking or damage.
锟斤拷If you found a concern with the hybrid low, 1-2 clutch regulator valve, repair or replace the valve or valve body.
9. Inspect the hybrid low, 1-2 clutch assembly for wear or damage.
锟斤拷If you found a hybrid low, 1-2 clutch assembly concern, repair or replace the low and reverse clutch assembly as necessary.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Valve Assembly Disassemble (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and
Repair/Overhaul/2ML70 - Automatic Transmission/54. Control Valve Assembly Disassemble) for valve body inspection procedures.
* Control Valve Upper Body Replacement (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Valve Body/Service and
Repair/2ML70 - Automatic Transmission) for control valve body replacement.
* Hybrid Low, 1-2 Clutch Piston Removal (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and
Repair/Overhaul/2ML70 - Automatic Transmission/24. Hybrid Low, 1-2 Clutch Piston Removal) for hybrid low, 1-2 clutch assembly
inspection.
* Hybrid Low, 1-2 Clutch Piston Installation (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Service and
Repair/Overhaul/2ML70 - Automatic Transmission/31. Hybrid Low, 1-2 Clutch Piston Installation) for low and hybrid low, 1-2 clutch
assembly replacement.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for control solenoid valve assembly replacement,
setup, and programming.
P079B
DTC P079B
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1808
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1808
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine idling, command the appropriate B52 HO2S heater to 100 % and 0 % with a scan tool while observing the B52 HO2S Heater Circuit
Test Status parameter. The parameter should display OK or Not Run.
2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.3-1.5 A.
3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan
tool. The parameter should not change with movement.
锟斤拷If movement affects the parameter, repair the appropriate harness or connector.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.
2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.
锟斤拷If the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests
normal and the B52 HO2S heater circuit fuse is open, test all components connected to the fuse and replace as necessary.
3. Probe the appropriate control circuit terminal listed below with a test lamp connected to B+. Verify that the test lamp does not illuminate.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
锟斤拷If the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.
4. Engine idling, the test lamp should illuminate, or flash.
锟斤拷If the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the
circuit/connections test normal, replace the K20 ECM.
Note:
* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain
ON and the scan tool will display greater than 0.00 amp.
* Performing this test may set additional DTCs.
5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.
锟斤拷If greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.
7. If all circuits test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine idling, command the appropriate B52 HO2S heater to 100 % and 0 % with a scan tool while observing the B52 HO2S Heater Circuit
Test Status parameter. The parameter should display OK or Not Run.
2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.3-1.5 A.
3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan
tool. The parameter should not change with movement.
锟斤拷If movement affects the parameter, repair the appropriate harness or connector.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.
2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.
锟斤拷If the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests
normal and the B52 HO2S heater circuit fuse is open, test all components connected to the fuse and replace as necessary.
3. Probe the appropriate control circuit terminal listed below with a test lamp connected to B+. Verify that the test lamp does not illuminate.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
锟斤拷If the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.
4. Engine idling, the test lamp should illuminate, or flash.
锟斤拷If the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the
circuit/connections test normal, replace the K20 ECM.
Note:
* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain
ON and the scan tool will display greater than 0.00 amp.
* Performing this test may set additional DTCs.
5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.
锟斤拷If greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.
7. If all circuits test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1791
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1791
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine idling, command the appropriate B52 HO2S heater to 100 % and 0 % with a scan tool while observing the B52 HO2S Heater Circuit
Test Status parameter. The parameter should display OK or Not Run.
2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.3-1.5 A.
3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan
tool. The parameter should not change with movement.
锟斤拷If movement affects the parameter, repair the appropriate harness or connector.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.
2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.
锟斤拷If the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests
normal and the B52 HO2S heater circuit fuse is open, test all components connected to the fuse and replace as necessary.
3. Probe the appropriate control circuit terminal listed below with a test lamp connected to B+. Verify that the test lamp does not illuminate.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
锟斤拷If the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.
4. Engine idling, the test lamp should illuminate, or flash.
锟斤拷If the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the
circuit/connections test normal, replace the K20 ECM.
Note:
* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain
ON and the scan tool will display greater than 0.00 amp.
* Performing this test may set additional DTCs.
5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.
锟斤拷If greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.
7. If all circuits test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Circuit/System Verification
1. Engine idling, command the appropriate B52 HO2S heater to 100 % and 0 % with a scan tool while observing the B52 HO2S Heater Circuit
Test Status parameter. The parameter should display OK or Not Run.
2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.3-1.5 A.
3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan
tool. The parameter should not change with movement.
锟斤拷If movement affects the parameter, repair the appropriate harness or connector.
4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the
conditions that you observed from the Freeze Frame/Failure Records data.
Circuit/System Testing
1. Ignition OFF, disconnect the harness connector at the appropriate B52 HO2S.
2. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.
锟斤拷If the test lamp does not illuminate, test the ignition voltage circuit for a short to ground or an open/high resistance. If the circuit tests
normal and the B52 HO2S heater circuit fuse is open, test all components connected to the fuse and replace as necessary.
3. Probe the appropriate control circuit terminal listed below with a test lamp connected to B+. Verify that the test lamp does not illuminate.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
锟斤拷If the test lamp illuminates, test the control circuit for a short to ground. If the circuit tests normal, replace the K20 ECM.
4. Engine idling, the test lamp should illuminate, or flash.
锟斤拷If the test lamp does not illuminate, or flash, test the control circuit for a short to voltage, or an open/high resistance. If the
circuit/connections test normal, replace the K20 ECM.
Note:
* Less than 10 ohm on the ignition voltage circuit, or control circuit may set a DTC. If there is resistance on a circuit the driver will remain
ON and the scan tool will display greater than 0.00 amp.
* Performing this test may set additional DTCs.
5. Ignition OFF, connect a 10 A fused jumper wire between the control circuit terminal listed below and the ignition voltage circuit terminal D.
* B52 HO2S 1 terminal E
* B52 HO2S 2 terminal C
6. Engine idling, observe the appropriate B52 HO2S Heater parameter. The scan tool should display 0.00 A.
锟斤拷If greater than the specified value, test the control circuit and the ignition voltage circuit for high resistance.
7. If all circuits test normal, test or replace the appropriate B52 HO2S.
Repair Instructions
Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (1500 Series) (See: Powertrain Management/Computers and Control
Systems/Oxygen Sensor/Service and Repair)Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (2500 Series) (See: Powertrain
Management/Computers and Control Systems/Oxygen Sensor/Service and Repair)
* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (1500 Series) (See: Powertrain Management/Computers and Control
Wednesday, October 30, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1634
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1634
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Turn the ignition OFF for 1 minute.
3. Turn the ignition ON.
4. Retest for DTC P1AF8 or P1AFE.
Circuit/System Testing
1. Verify that DTCs P0C01, P0C04, P0BFD, or P0BFE is not set.
锟斤拷If the DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic
Trouble Code (DTC) List - Vehicle).
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
2. Disable the high voltage for servicing at the drive motor generator control module assembly cable connections. Refer to High Voltage
Disabling ().
3. Inspect for damaged 3 phase cables between the PIM and the transmission.
锟斤拷If damage is observed, replace the 3 phase cables.
4. Inspect the 3 phase cable terminal fasteners for the proper torque and for arc-flash damage.
锟斤拷If any fasteners were loose and no arc flash damage is present, torque the fasteners and re-assemble the vehicle. Retest for the DTC.
锟斤拷If any fasteners were loose and arc flash damage is present, replace the PIM and the 3 phase cable assembly.
5. Remove the 3 phase cable assembly from the PIM distribution box. Refer to Generator Control Module 3-Phase Cable Assembly
Replacement ().
6. Test the resistance of each phase by measuring between the following circuits with a DMM.
* Phase U and phase V
* Phase U and phase W
锟斤拷If you measure 0.5 ohms or less, continue with Circuit/System Testing.
锟斤拷If you measure more than 0.5 ohms, proceed to Open Phase Testing Procedure below.
7. Test the resistance to ground for each phase of the applicable drive motor generator by measuring between the following points with a DMM.
* Phase U terminal and chassis ground
* Phase V terminal and chassis ground
* Phase W terminal and chassis ground
锟斤拷If infinite resistance is measured, replace the 3-phase cable assembly and the drive motor generator assembly that corresponds to the set
DTC and retest for the DTC. If the DTC resets replace the PIM.
锟斤拷If less than infinite is measured, continue with Circuit/System Testing.
8. Remove the 3-phase cable assembly from the transmission. Refer to Generator Control Module 3-Phase Cable Assembly Replacement ().
Ensure the terminals are not contacting chassis ground.
9. Retest the resistance to ground for each phase of the 3-phase cable. Measure between the following points with a DMM.
* Phase U terminal and shield ground
* Phase V terminal and shield ground
* Phase W terminal and shield ground
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Turn the ignition OFF for 1 minute.
3. Turn the ignition ON.
4. Retest for DTC P1AF8 or P1AFE.
Circuit/System Testing
1. Verify that DTCs P0C01, P0C04, P0BFD, or P0BFE is not set.
锟斤拷If the DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic
Trouble Code (DTC) List - Vehicle).
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
2. Disable the high voltage for servicing at the drive motor generator control module assembly cable connections. Refer to High Voltage
Disabling ().
3. Inspect for damaged 3 phase cables between the PIM and the transmission.
锟斤拷If damage is observed, replace the 3 phase cables.
4. Inspect the 3 phase cable terminal fasteners for the proper torque and for arc-flash damage.
锟斤拷If any fasteners were loose and no arc flash damage is present, torque the fasteners and re-assemble the vehicle. Retest for the DTC.
锟斤拷If any fasteners were loose and arc flash damage is present, replace the PIM and the 3 phase cable assembly.
5. Remove the 3 phase cable assembly from the PIM distribution box. Refer to Generator Control Module 3-Phase Cable Assembly
Replacement ().
6. Test the resistance of each phase by measuring between the following circuits with a DMM.
* Phase U and phase V
* Phase U and phase W
锟斤拷If you measure 0.5 ohms or less, continue with Circuit/System Testing.
锟斤拷If you measure more than 0.5 ohms, proceed to Open Phase Testing Procedure below.
7. Test the resistance to ground for each phase of the applicable drive motor generator by measuring between the following points with a DMM.
* Phase U terminal and chassis ground
* Phase V terminal and chassis ground
* Phase W terminal and chassis ground
锟斤拷If infinite resistance is measured, replace the 3-phase cable assembly and the drive motor generator assembly that corresponds to the set
DTC and retest for the DTC. If the DTC resets replace the PIM.
锟斤拷If less than infinite is measured, continue with Circuit/System Testing.
8. Remove the 3-phase cable assembly from the transmission. Refer to Generator Control Module 3-Phase Cable Assembly Replacement ().
Ensure the terminals are not contacting chassis ground.
9. Retest the resistance to ground for each phase of the 3-phase cable. Measure between the following points with a DMM.
* Phase U terminal and shield ground
* Phase V terminal and shield ground
* Phase W terminal and shield ground
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1631
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1631
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
Important: DTC P1AE7 must test and pass before performing this diagnostic procedure.
1. Inspect for DTC P1AE7.
锟斤拷If the DTC has set, a loss of isolation condition within the hybrid battery has caused this DTC to set. Refer to DTC P1AE6 or P1AE7 (
See: P Code Charts/P1AE6).
2. Clear the DTC information.
3. Turn the ignition OFF for 1 minute.
4. Turn the ignition ON.
5. Retest for DTCs P1AF4, P1AF5, P1AF6 and P1AF7.
Circuit/System Testing
Important: DTC P1AE7 must test and pass before performing this diagnostic procedure.
1. Inspect for DTC P1AE7.
锟斤拷If the DTC has set, a loss of isolation condition within the hybrid battery has caused this DTC to set. Refer to DTC P1AE6 or P1AE7 (
See: P Code Charts/P1AE6).
2. Ignition ON, retest for DTCs P1AF4, P1AF5, P1AF6 and P1AF7.
锟斤拷If the DTC resets, program the PIM with the latest software version and recheck for DTCs. If the DTC resets after programming or if the
PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P1AF7
DTC P1AF4-P1AF7
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P1AF4
- Drive Motor 1 Control Module Hybrid Battery Voltage Isolation Sensor Circuit Low Voltage
DTC P1AF5
- Drive Motor 1 Control Module Hybrid Battery Voltage Isolation Sensor Circuit High Voltage
DTC P1AF6
- Drive Motor 2 Control Module Hybrid Battery Voltage Isolation Sensor Circuit Low Voltage
DTC P1AF7
- Drive Motor 2 Control Module Hybrid Battery Voltage Isolation Sensor Circuit High Voltage
Circuit/System Description
The drive motor generator power inverter control module (PIM) contains two motor control modules (MCMs). Each MCM measures hybrid battery
high voltage (HV) with several internal sensors. The MCMs test for loss of isolation (LOI) between either the HV positive circuit or HV negative
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
Important: DTC P1AE7 must test and pass before performing this diagnostic procedure.
1. Inspect for DTC P1AE7.
锟斤拷If the DTC has set, a loss of isolation condition within the hybrid battery has caused this DTC to set. Refer to DTC P1AE6 or P1AE7 (
See: P Code Charts/P1AE6).
2. Clear the DTC information.
3. Turn the ignition OFF for 1 minute.
4. Turn the ignition ON.
5. Retest for DTCs P1AF4, P1AF5, P1AF6 and P1AF7.
Circuit/System Testing
Important: DTC P1AE7 must test and pass before performing this diagnostic procedure.
1. Inspect for DTC P1AE7.
锟斤拷If the DTC has set, a loss of isolation condition within the hybrid battery has caused this DTC to set. Refer to DTC P1AE6 or P1AE7 (
See: P Code Charts/P1AE6).
2. Ignition ON, retest for DTCs P1AF4, P1AF5, P1AF6 and P1AF7.
锟斤拷If the DTC resets, program the PIM with the latest software version and recheck for DTCs. If the DTC resets after programming or if the
PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P1AF7
DTC P1AF4-P1AF7
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P1AF4
- Drive Motor 1 Control Module Hybrid Battery Voltage Isolation Sensor Circuit Low Voltage
DTC P1AF5
- Drive Motor 1 Control Module Hybrid Battery Voltage Isolation Sensor Circuit High Voltage
DTC P1AF6
- Drive Motor 2 Control Module Hybrid Battery Voltage Isolation Sensor Circuit Low Voltage
DTC P1AF7
- Drive Motor 2 Control Module Hybrid Battery Voltage Isolation Sensor Circuit High Voltage
Circuit/System Description
The drive motor generator power inverter control module (PIM) contains two motor control modules (MCMs). Each MCM measures hybrid battery
high voltage (HV) with several internal sensors. The MCMs test for loss of isolation (LOI) between either the HV positive circuit or HV negative
Tuesday, October 29, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1497
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1497
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Circuit/System Verification
1. Clear the DTC information.
2. Turn the ignition OFF for 2 minutes.
3. Turn the ignition ON.
4. Operate the vehicle within the conditions for running and setting.
5. Retest for the DTC.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Perform the High Voltage Disabling () procedure for servicing at the drive motor generator control module cable connections.
2. Remove the 3-phase cable assembly from the PIM distribution box. Refer to Generator Control Module 3-Phase Cable Assembly
Replacement ().
3. Test the resistance to ground for each phase of the applicable drive motor generator by measuring between the following points with a DMM.
* Phase U terminal and chassis ground
* Phase V terminal and chassis ground
* Phase W terminal and chassis ground
锟斤拷If less than infinite is measured, continue with Circuit/System Testing.
锟斤拷If infinite resistance is measured, replace the drive motor generator assembly that corresponds to the set DTC and retest for DTCs. If
DTC P0C01 or P0C04 still resets, replace the PIM.
4. Remove the 3-phase cable assembly from the transmission. Refer to Generator Control Module 3-Phase Cable Assembly Replacement ().
Ensure the terminals are not contacting chassis ground.
5. Retest the resistance to ground for each phase of the 3-phase cable. Measure between the following points with a DMM.
* Phase U terminal and the shield ground
* Phase V terminal and the shield ground
* Phase W terminal and the shield ground
锟斤拷If infinite resistance is measured, replace the applicable drive motor generator.
锟斤拷If less than infinite is measured, replace the generator control module 3-phase cable assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
* Generator Control Module 3-Phase Cable Assembly Replacement ()
* Drive Motor with Generator Assembly Removal - 1st Position (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic Transmission/8. Drive Motor with Generator Assembly Removal -
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Electrical Information Reference
* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit
Testing/Circuit Testing)
* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic
Procedures/Connector Repairs/Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General
Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring
Repairs/Wiring Repairs)
Circuit/System Verification
1. Clear the DTC information.
2. Turn the ignition OFF for 2 minutes.
3. Turn the ignition ON.
4. Operate the vehicle within the conditions for running and setting.
5. Retest for the DTC.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Perform the High Voltage Disabling () procedure for servicing at the drive motor generator control module cable connections.
2. Remove the 3-phase cable assembly from the PIM distribution box. Refer to Generator Control Module 3-Phase Cable Assembly
Replacement ().
3. Test the resistance to ground for each phase of the applicable drive motor generator by measuring between the following points with a DMM.
* Phase U terminal and chassis ground
* Phase V terminal and chassis ground
* Phase W terminal and chassis ground
锟斤拷If less than infinite is measured, continue with Circuit/System Testing.
锟斤拷If infinite resistance is measured, replace the drive motor generator assembly that corresponds to the set DTC and retest for DTCs. If
DTC P0C01 or P0C04 still resets, replace the PIM.
4. Remove the 3-phase cable assembly from the transmission. Refer to Generator Control Module 3-Phase Cable Assembly Replacement ().
Ensure the terminals are not contacting chassis ground.
5. Retest the resistance to ground for each phase of the 3-phase cable. Measure between the following points with a DMM.
* Phase U terminal and the shield ground
* Phase V terminal and the shield ground
* Phase W terminal and the shield ground
锟斤拷If infinite resistance is measured, replace the applicable drive motor generator.
锟斤拷If less than infinite is measured, replace the generator control module 3-phase cable assembly.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
* Generator Control Module 3-Phase Cable Assembly Replacement ()
* Drive Motor with Generator Assembly Removal - 1st Position (See: Transmission and Drivetrain/Automatic
Transmission/Transaxle/Service and Repair/Overhaul/2ML70 - Automatic Transmission/8. Drive Motor with Generator Assembly Removal -
Monday, October 28, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1386
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1386
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
* EL-48571 High Voltage Battery Pin Out Box
* EL-48900 HEV Safety Kit
Circuit/System Verification
Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V, and all readings should be within 1.5
V of each other.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B9D
DTC P0B3E, P0B43, P0B48, P0B4D, P0B52, P0B57, P0B5C, P0B61, P0B66, P0B6B, P0B70, P0B75, P0B7A, P0B7F, P0B84, P0B89, P0B8E,
P0B93, P0B98, or P0B9D
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
* EL-48571 High Voltage Battery Pin Out Box
* EL-48900 HEV Safety Kit
Circuit/System Verification
Ignition ON, observe the scan tool Hybrid Battery 1-20 parameters. Each reading should be between 10-19 V, and all readings should be within 1.5
V of each other.
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Disconnect the X4 harness connector at the drive motor battery control module.
3. Connect the EL-48571 high voltage battery pin out box.
4. Install the high voltage manual disconnect lever. Measure and record each of the 20 battery voltages.
5. Each battery voltage reading should be between 10-19 V.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
6. Each battery voltage reading should be within 1.5 V of each other.
锟斤拷If not within the specified range, replace the drive motor battery assembly.
7. If all circuits test normal, replace the drive motor generator battery control module.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.
* Drive Motor Generator Battery Replacement and Shipping Preparation ()
* Control Module References (See: Testing and Inspection/Programming and Relearning) for drive motor generator battery control module
replacement, setup and programming
P0B9D
DTC P0B3E, P0B43, P0B48, P0B4D, P0B52, P0B57, P0B5C, P0B61, P0B66, P0B6B, P0B70, P0B75, P0B7A, P0B7F, P0B84, P0B89, P0B8E,
P0B93, P0B98, or P0B9D
Sunday, October 27, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1297
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1297
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Ignition ON.
4. Retest for DTCs P0BE6, P0BE7, P0BE8, P0BEA, P0BEB, P0BEC, P0BEE, P0BEF, P0BF0, P0BF2, P0BF3, P0BF4, P0BF6, P0BF7,
P0BF8, P0BFA, P0BFB or P0BFC.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE8
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0BE6
- Drive Motor 1 Phase U Current Sensor Performance
DTC P0BE7
- Drive Motor 1 Phase U Current Sensor Circuit Low Voltage
DTC P0BE8
- Drive Motor 1 Phase U Current Sensor Circuit High Voltage
DTC P0BEA
- Drive Motor 1 Phase V Current Sensor Performance
DTC P0BEB
- Drive Motor 1 Phase V Current Sensor Circuit Low Voltage
DTC P0BEC
- Drive Motor 1 Phase V Current Sensor Circuit High Voltage
DTC P0BEE
- Drive Motor 1 Phase W Current Sensor Performance
DTC P0BEF
- Drive Motor 1 Phase W Current Sensor Circuit Low Voltage
DTC P0BF0
- Drive Motor 1 Phase W Current Sensor Circuit High Voltage
DTC P0BF2
- Drive Motor 2 Phase U Current Sensor Performance
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Circuit/System Verification
1. Clear the DTC information.
2. Ignition OFF for 1 minute.
3. Ignition ON.
4. Retest for DTCs P0BE6, P0BE7, P0BE8, P0BEA, P0BEB, P0BEC, P0BEE, P0BEF, P0BF0, P0BF2, P0BF3, P0BF4, P0BF6, P0BF7,
P0BF8, P0BFA, P0BFB or P0BFC.
Circuit/System Testing
Program the PIM with the latest software version and recheck for DTCs.
If the DTC resets after programming or if the PIM already contains the latest software version, replace the PIM.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
Control Module References (See: Testing and Inspection/Programming and Relearning) for PIM replacement, setup, and programming.
P0BE8
DTC P0BE6-P0BE8, P0BEA-P0BEC, P0BEE, P0BEF, P0BF0, P0BF2-P0BF4, P0BF6-P0BF8, or P0BFA-P0BFC
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach.
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC P0BE6
- Drive Motor 1 Phase U Current Sensor Performance
DTC P0BE7
- Drive Motor 1 Phase U Current Sensor Circuit Low Voltage
DTC P0BE8
- Drive Motor 1 Phase U Current Sensor Circuit High Voltage
DTC P0BEA
- Drive Motor 1 Phase V Current Sensor Performance
DTC P0BEB
- Drive Motor 1 Phase V Current Sensor Circuit Low Voltage
DTC P0BEC
- Drive Motor 1 Phase V Current Sensor Circuit High Voltage
DTC P0BEE
- Drive Motor 1 Phase W Current Sensor Performance
DTC P0BEF
- Drive Motor 1 Phase W Current Sensor Circuit Low Voltage
DTC P0BF0
- Drive Motor 1 Phase W Current Sensor Circuit High Voltage
DTC P0BF2
- Drive Motor 2 Phase U Current Sensor Performance
Saturday, October 26, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1222
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1222
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Friday, October 25, 2019
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1146
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1146
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1143
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1143
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1140
2010 Cadillac Truck Escalade ESV AWD V8-6.2L Page 1140
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code
(DTC) Type Definitions)
Scan Tool Reference
Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information
Special Tools
EL-48900 HEV Safety Kit
Circuit/System Verification
1. Verify that DTC P0A80, P0A81 or P0BBD is not set.
锟斤拷If any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code
Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle),
2. Ignition ON, observe the scan tool BECM hybrid battery temperature parameters. The readings should be between -39 and +95锟斤拷C (-38.2 and
+203锟斤拷F) with no greater than a 15锟斤拷C ( 59锟斤拷F) difference between any of the four temperature sensor readings. Refer to Temperature Versus
Resistance ().
Circuit/System Testing
Danger: Always perform the High Voltage Disabling procedure prior to servicing any High Voltage component or connection.
Personal Protection Equipment (PPE) and proper procedures must be followed.
The High Voltage Disabling procedure will perform the following tasks:
* Identify how to disable high voltage.
* Identify how to test for the presence of high voltage.
* Identify condition under which high voltage is always present and personal protection equipment (PPE) and proper procedures
must be followed.
Before working on any high voltage system, be sure to wear the following Personal Protection Equipment:
* Safety glasses with appropriate side shields when within 50 feet of the vehicle, either indoors or outdoors.
* Certified and up-to-date Class "0" Insulation gloves rated at 1000V with leather protectors.
- Visually and functionally inspect the gloves before use.
- Wear the Insulation gloves at all times when working with the high voltage battery assembly, whether the system is energized or
not.
Failure to follow the procedures exactly as written may result in serious injury or death.
1. Ignition OFF, disable the high voltage at the drive motor generator battery. Refer to High Voltage Disabling ().
2. Verify that none of the following conditions exist:
* the inlet and outlet air vents do not have any obstructions or blockages
* the vent fan blades are not broken or damaged
* the internal foam seals are not missing or damaged
锟斤拷If any conditions are found, remove, repair or replace as necessary.
3. Ignition OFF, disconnect the X3 harness connector at the drive motor generator battery control module.
4. Test for 1k ohm-209k ohm between each of the terminals listed below. The resistance of each temperature sensor should be within the
specified range, and within 500 ohm of each other. Refer to Temperature Versus Resistance ().
* Sensor 1-5 V reference circuit terminal 1 and low reference circuit terminal 2
* Sensor 2-5 V Reference circuit terminal 3 and low reference circuit terminal 4
* Sensor 3-5 V Reference circuit terminal 5 and low reference circuit terminal 6
* Sensor 4-5 V Reference circuit terminal 7 and low reference circuit terminal 8
锟斤拷If not within the specified range, replace the drive motor battery sensor module wiring harness.
5. If all circuits test normal, replace the drive motor generator battery control module.
Subscribe to:
Posts (Atom)