2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 659
replace the MSM.
5. If all circuit test normal, test or replace the tilt switch.
Component Testing
Tilt Switch
1. Ignition OFF, disconnect the harness connector at the tilt switch.
2. Test for infinite resistance between the control terminals A and C with the switch in the neutral position.
瀚慖f less than the specified range, replace the tilt switch.
3. Test for less than 1 ohm between the control terminals listed below and the B+ terminal B with the switch in each appropriate position.
* Tilt Up Switch terminal C
* Tilt Down Switch terminal A
瀚慖f greater than the specified value, replace the tilt switch.
Repair Instructions
Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.
* Steering Column Tilt Wheel Switch Replacement (See: Sensors and Switches/Sensors and Switches - Steering and Suspension/Sensors and
Switches - Steering/Tilt Wheel Switch/Service and Repair)
* Control Module References (See: Testing and Inspection/Programming and Relearning) for MSM replacement, setup, and programming
B2875
DTC B2850, B2855, B2870, or B2875
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System
Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an
overview of the diagnostic approach
* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure
Instructions) provides an overview of each diagnostic category
DTC Descriptor
DTC B2870 01
- Tilt Up Switch Circuit Short to Battery
DTC B2875 01
- Tilt Down Switch Circuit Short to Battery
Diagnostic Fault Information
Circuit Description
The memory seat module (MSM) receives voltage inputs from the tilt switch based on the position of the switch. The MSM then supplies battery
voltage and a ground to the tilt motor control circuits depending on which direction of movement is requested.
Conditions for Running the DTC
The ignition ON.
Conditions for Setting the DTC
The MSM detects a tilt switch input for more than 30 consecutive seconds after the tilt motor movement has stopped.
Showing posts with label replace the MSM.. Show all posts
Showing posts with label replace the MSM.. Show all posts
Wednesday, December 4, 2019
Wednesday, November 27, 2019
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 515
2010 Cadillac Truck Escalade RWD V8-6.0L Hybrid Page 515
瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.
5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver
Seat Recline Sensor parameter is greater than 4.75 volts.
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat recline position sensor.
B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06
1. Ignition OFF, disconnect the X2 harness connector at the seat adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool driver seat sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
* Seat horizontal position sensor terminal 3
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal 6. Verify the
appropriate scan tool driver seat position sensor parameter is greater than 4.75 volts.
* Seat horizontal position sensor terminal 3
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat position sensor.
B1850 01, B1850 06, B1860 01 or B1860 06
1. Ignition OFF, disconnect the X2 harness connector at the lumbar adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal C and ground.
瀚慖f greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool lumbar sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal A. Verify the
appropriate scan tool lumbar sensor parameter is greater than 4.75 volts.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.
5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver
Seat Recline Sensor parameter is greater than 4.75 volts.
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat recline position sensor.
B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06
1. Ignition OFF, disconnect the X2 harness connector at the seat adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool driver seat sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
* Seat horizontal position sensor terminal 3
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal 6. Verify the
appropriate scan tool driver seat position sensor parameter is greater than 4.75 volts.
* Seat horizontal position sensor terminal 3
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat position sensor.
B1850 01, B1850 06, B1860 01 or B1860 06
1. Ignition OFF, disconnect the X2 harness connector at the lumbar adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal C and ground.
瀚慖f greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool lumbar sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal A. Verify the
appropriate scan tool lumbar sensor parameter is greater than 4.75 volts.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
Thursday, November 14, 2019
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 578
2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 578
瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.
5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver
Seat Recline Sensor parameter is greater than 4.75 volts.
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat recline position sensor.
B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06
1. Ignition OFF, disconnect the X2 harness connector at the seat adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool driver seat sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
* Seat horizontal position sensor terminal 3
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal 6. Verify the
appropriate scan tool driver seat position sensor parameter is greater than 4.75 volts.
* Seat horizontal position sensor terminal 3
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat position sensor.
B1850 01, B1850 06, B1860 01 or B1860 06
1. Ignition OFF, disconnect the X2 harness connector at the lumbar adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal C and ground.
瀚慖f greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool lumbar sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal A. Verify the
appropriate scan tool lumbar sensor parameter is greater than 4.75 volts.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
瀚慖f greater than the specified range, test the signal circuit terminal 2 for a short to voltage. If the circuit tests normal, replace the MSM.
5. Install a 3A fused jumper wire between the signal circuit terminal 2 and the 5-volt reference circuit terminal 3. Verify the scan tool Driver
Seat Recline Sensor parameter is greater than 4.75 volts.
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat recline position sensor.
B2355 01, B2355 06, B2365 01, B2365 06, B2375 01 or B2375 06
1. Ignition OFF, disconnect the X2 harness connector at the seat adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal 2 and ground.
瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal 6 and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool driver seat sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
* Seat horizontal position sensor terminal 3
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal 6. Verify the
appropriate scan tool driver seat position sensor parameter is greater than 4.75 volts.
* Seat horizontal position sensor terminal 3
* Seat front vertical position sensor terminal 1
* Seat rear vertical position sensor terminal 5
瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the
MSM.
6. If all circuits test normal, test or replace the seat position sensor.
B1850 01, B1850 06, B1860 01 or B1860 06
1. Ignition OFF, disconnect the X2 harness connector at the lumbar adjuster assembly.
2. Test for less than 2 ohms between the low reference circuit terminal C and ground.
瀚慖f greater than the specified value, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the MSM.
3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.
瀚慖f less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the MSM.
瀚慖f greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the MSM.
4. Verify the appropriate scan tool lumbar sensor parameter is less than 1 volt.
瀚慖f greater than the specified range, test the appropriate signal circuit listed below for a short to voltage. If the circuit tests normal, replace
the MSM.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
5. Install a 3A fused jumper wire between the appropriate signal circuit listed below and the 5-volt reference circuit terminal A. Verify the
appropriate scan tool lumbar sensor parameter is greater than 4.75 volts.
* Lumbar vertical position sensor terminal B
* Lumbar horizontal position sensor terminal D
Subscribe to:
Posts (Atom)