Saturday, November 9, 2019

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 2631

2010 Cadillac Truck Escalade EXT AWD V8-6.2L Page 2631

* The engine speed is between 1,100-2,500 RPM.

* The mass air flow (MAF) is between 3-20 g/s.

* The vehicle speed is between 50-120 km/h (31-75 mph).

* The fuel level is greater than 10 percent.

* The fuel system is in Closed Loop.

* The catalytic converter temperature is between 550-900掳C (1,022-1,652掳F).

* The DTCs run once per ignition cycle when the above conditions are met.

Conditions for Setting the DTC

P2270

The ECM does not detect a HO2S voltage greater than 805 mV before accumulated mass air flow exceeds 550 grams.

P2272

The ECM does not detect a HO2S voltage greater than 775 mV before the accumulated mass air flow exceeds 82 grams.

Action Taken When the DTC Sets

DTCs P2270 and P2272 are Type B DTCs.

Conditions for Clearing the DTC

DTCs P2270 and P2272 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify that no B52 HO2S heater DTCs are set.

瀚慖f any B52 HO2S heater DTCs are set, perform those diagnostics first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See:

Diagnostic Trouble Code Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine idling, move the appropriate B52 HO2S 2 harness connector and the engine control module (ECM) harness connector while

monitoring the B52 HO2S 2 voltage parameter with a scan tool. Verify that the B52 HO2S parameter does not change abruptly while moving

the related harnesses.

瀚慖f the B52 HO2S parameter does change abruptly while moving the related harnesses repair the circuit as necessary.

3. Engine idling at operating temperature, observe the appropriate B52 HO2S 2 parameter with a scan tool. Verify the following:

* The B52 HO2S 1 value should vary from below 200 mV to above 800 mV and respond to fueling changes.